Cyclone screwdriver is a kind of pneumatic tool. Pneumatic screwdriver is a tool that is often used in assembly production. Since the factory needs to produce for a long time, in order to prevent the frequent failure of the pneumatic screwdriver in use, it guarantee For the normal operation of production, it is necessary to know the skills of using pneumatic screwdrivers.
Â
　 Tips for using pneumatic screwdriver
Â
1. Check before use and have someone in charge.
2. If any missing parts or damaged parts are found, repair them in time, otherwise they cannot be used.
3. The sleeve does not completely cover the nut (screw slot), and it is strictly forbidden to press the switch.
4. The sleeve connection must be connected with special pins and sealed with aprons. (Screwdriver clamping type)
5. It is forbidden to load and unload the pneumatic wrench sleeve and the pneumatic cleaning pneumatic wrench with the wind (without closing the air valve).
6. Without permission of the person in charge, all kinds of equipment are not allowed to be opened or supplied without authorization.
7. After all kinds of equipment are used up, remove the quick connector, clean it and keep it in a safe place.
8. When using, do not overload, do not run at high speed to prevent premature wear of the machine.
9. Each shift must be filled with lubricating oil 3 to 4 times from the inner hole of the receiving pipe. No. 20 motor oil can be used in summer and No. 10 motor oil in winter.
10. If a secondary impact is found during use, it should be immediately shut down for inspection. It is forbidden to disassemble on site (refer to the unclean place) and should be promptly sent to the repair department for inspection.
Â
Pneumatic screwdriver maintenance
Â
1. Periodically (about once a week) check and maintain tools, add butter to rotating parts such as bearings, and add engine oil to air motor parts.
2. Choose appropriate tools to work. Too large tools can easily cause work injury, too small tools can easily cause tool damage.
3. The correct replacement air supply system: the inlet pressure at the tool inlet (outlet pressure of the non-air compressor) is generally 90PSIG (6.2Kg / cm ^ 2), too high and too low can damage the performance and life of the tool ; The intake air must contain sufficient lubricating oil to allow the air motor in the tool to be fully lubricated (you can place a white paper at the exhaust of the tool to check whether there is oil stains, normally it is oil stains); It is not appropriate to constrict air without an air dryer.
4. When using various tools, be sure to follow various safety regulations and instructions.
5. If the tool has a slight failure or cannot reach the original function after use, it can not be used any more, and it should be checked immediately.
6. It is not allowed to arbitrarily remove parts of the tool before operation, except that it will affect the safety of the operator and cause damage to the tool.
The above is the knowledge about the use skills and maintenance of pneumatic screwdrivers. I hope that the two knowledge points shared can make friends more standardized and pay more attention to the maintenance of pneumatic screwdrivers in order to make the screwdriver use. Longer life.
Wood Grain Texture PU Sandwich Panel
Wood Grain Texture PU Sandwich Panel
Rich selection of textures and colors meet different decoration requirements, giving the city and the buildings a new look.
The PU foam is the most advanced and eco-friendly insulation material in the world. With the help of the back aluminum foil, the thermal preservation effect achieves the best.
The unique structure prevents the heat loss in winter. Meanwhile it reduces the heat of the summer sunshine.
Aceta paintcoat and flurocarbon paint of weather resistance performance are applied on surface of wall panel. It is reserved with superior self-cleaning, weather resistance, corrosion resistance and acid& alkali resistance performance.
Light weight with 3.7Kgs/m2 makes the installation easy.
The installation process is clean and tidy without any noise and dust, construction waste.
Different selections of accessories meet different effects.
High quality and stable performance: Manufactured in CNC automation production line, the product pass rate can reach 99.9% with stable chemical structure and physical structure.
Cladding Siding,Wood Insulation Wall Planks,Wood Look Wall Panels,Wood Grain Texture Pu Sandwich Panel
Jinan Zhengtang Insulation Decoration Material Co.Ltd , https://www.ztwallsiding.com