Plywood doors are used in many homes, such as bedroom doors, toilet doors, balcony doors, etc. These "doors" can be used as plywood doors, so it can also be called indoor special doors. The use of the plywood door is very extensive, so its installation process must be fine, so as not to affect everyone's life safety. If the splint door is not well installed, there is a possibility of slumping. It is best to check the ply door when it is installed many times. Then let me introduce how to install the plywood door.
Plywood door production operation
1. Plywood door production operation procedures and general requirements:
Door and window production operation procedures: batching → cutting → planing → chiseling → opening, cutting → finishing line angle → stacking → assembling;
2. Ingredients and materials for construction
1) Ingredients and cut-offs should pay special attention to careful calculation and matching, and should not be used for large materials and long materials. When using species of masson pine, casuarina, birch, poplar, and insects, the whole component should be treated with anti-corrosion and insect-repellent agents. ;
2) It is necessary to determine the machining allowance reasonably. The processing allowance of width and thickness is 3mm for one plane, and 5mm for both sides. For components with a length of 50cm or less, the machining allowance can be 3-4mm;
3) When the door frame material has a smooth bend, the curvature should not exceed 4mm. The bender is generally not allowed to use;
4) Green skin and inverted sputum can be used if they are perfect on the front and the cut. If the back is more than 1/6 of the thickness of the wood and 1/5 of the length, it is generally not allowed to use.
Plywood door installation process
(1) The interior of the finished plywood door can be installed after the basic decoration is completed.
(2) After the finished door enters the site, it is necessary to carry out careful inspection and set up a special stacking ground to prevent it from being damaged or raining.
(3) The door frame with good safety is protected by an adhesive multi-layer board to prevent collision.
(4) The hardware should be in the correct position and fixed with wood screws. It should not be replaced by iron nails. It should be drilled into 1/3 depth first, then tightened and screwed. It is strictly prohibited to drive all depths.
(5) Before the installation of the plywood door frame, the outside of the frame shall be treated with anti-corrosion treatment. After the door leaf is installed, the flatness and diagonal inspection shall be carried out.
(6) The splint door leaf must be installed firmly, the switch is flexible, the closing is tight, and there is no flapping.
(7) The surface of the plywood door is clean, no shading or hammering; the cutting angle of the wooden door and the seam are tight and flat; the door and window frame and the fan cutting edge are straight and the planing surface is flat; the groove and the hole edge on the plywood door are neat and burr-free.
Be sure to pay attention when installing the plywood door. The plywood door belongs to a very light skeleton door. It has thin-walled doors made of different materials on both sides, including plywood and fiberboard. These two materials are used for plywood door selection. The point is that if the material of the plywood door is less than one of them, it is not a qualified splint door. Before installation, be sure to pay attention to the installation, do not be wet, otherwise it will be prone to degumming. Tips, do not install the splint door on the outer door.
About Materials: We have 3 types of paper.
1. Art paper, this material is disposable material which is not waterproof and tearproof2. Synthetic paper, which is waterproof and tear-proof.
3. Tyvek paper, also called Dupont paper, this material is also tearproof and waterproof, and it is sofer and lighter than the Synthetic paper
About Size:
The size of the paper tape measure can be completely customized.
The maximum length that we can make is 160cm/62inch.
The standard width is 20mm. And wider size like 25mm, 30mm is also workable for us.
About Usage:
1. Art paper tape measure is widely used in medical area, such as wound measuring tape. It is disposable and it prevents cross-infection.
Measure in both inches or centimeters on one side, so you can record the units that are most appropriate for each patient visit.
2. Synthetic paper tape measure contains full color custom printing information on both sides.
It is used for multiple purposes such as measuring child height, circumference of furniture, room space calculating, etc. The synthetic paper is strong and resistant to water and tear, it can be used repeatedly.
3. Tyvek paper tape measure is Latex-Free, it prevents reactions in patients with a latex allergy when you use Tyvek paper measuring tapes.
They are made without latex to make it easier to accommodate people with allergies in your office, so you can provide the best level of patient care.
Medical Tape Measure, Medical Measuring Ruler, Paper Ruler, Paper Measuring Ruler, Bra Size Measuring Tape, Disposable Tape Measure
Wintape Measuring Tape Company , https://www.wintapetapemeasure.com