The installation effect on the wing gate is very important. It determines the acceptance of the entire project. How to properly install the wing gate should pay attention to the following issues:
First, wing gate determination program. In the communication with the customer to determine the program, the site width, length, how many machines can be clearly defined, is the choice of vertical wing gate, or bridge wing gate, vertical wing gate size: 420x330x980 (mm), bridge wings Gate size: 1200x280x1000(mm),, wing gate rod to chassis size 510mm, ie, vertical wing gate area: 420x(330+510), bridge wing area 1200x(280+510), determined When selecting the type, fully consider the gap between the gate and the brake lever, the area occupied by each wing gate, the placement position, and how to route the cable (whether it is going through the open line or the dark line). The plan is set, the target is set, and the wing gate is waiting. on site.
Second, fixed position wiring. According to the previously determined plan, the specific size of the wing gate should be clearly defined, and the pre-embedded pipe should be completed. The gap between the gate and the gate should be 50-100mm. The upper cover can be opened to prevent adjustment of the machine and maintenance. Leave gaps between the gates and gates to embed 2 plastic pipes with 6 points to 8 points. One hose takes the power line (strong power), and the other hose takes the signal line (weak current). The signal line takes a rubber hose at the same time, which will affect the communication effect. The buried pipe should be exposed to the ground with a height of 30-40mm. The vertical wing gate should be at the bottom of the machine and the bridge wing should be good on both sides. (Because the bridge bottom of the bridge wing is closed).
Third, fixed adjustments. The fixed bottom is fixed with a 4-M10x100 expansion screw, which cannot be swayed. The whole machine is horizontal and the overall appearance is consistent. It is better to use a thin line to pull a straight line before and after fixing, and the vertical and horizontal directions are consistent. The wing gate and the wing gate are connected in series, one by one. Adjustment, straight lines can be used normally.
First, wing gate determination program. In the communication with the customer to determine the program, the site width, length, how many machines can be clearly defined, is the choice of vertical wing gate, or bridge wing gate, vertical wing gate size: 420x330x980 (mm), bridge wings Gate size: 1200x280x1000(mm),, wing gate rod to chassis size 510mm, ie, vertical wing gate area: 420x(330+510), bridge wing area 1200x(280+510), determined When selecting the type, fully consider the gap between the gate and the brake lever, the area occupied by each wing gate, the placement position, and how to route the cable (whether it is going through the open line or the dark line). The plan is set, the target is set, and the wing gate is waiting. on site.
Second, fixed position wiring. According to the previously determined plan, the specific size of the wing gate should be clearly defined, and the pre-embedded pipe should be completed. The gap between the gate and the gate should be 50-100mm. The upper cover can be opened to prevent adjustment of the machine and maintenance. Leave gaps between the gates and gates to embed 2 plastic pipes with 6 points to 8 points. One hose takes the power line (strong power), and the other hose takes the signal line (weak current). The signal line takes a rubber hose at the same time, which will affect the communication effect. The buried pipe should be exposed to the ground with a height of 30-40mm. The vertical wing gate should be at the bottom of the machine and the bridge wing should be good on both sides. (Because the bridge bottom of the bridge wing is closed).
Third, fixed adjustments. The fixed bottom is fixed with a 4-M10x100 expansion screw, which cannot be swayed. The whole machine is horizontal and the overall appearance is consistent. It is better to use a thin line to pull a straight line before and after fixing, and the vertical and horizontal directions are consistent. The wing gate and the wing gate are connected in series, one by one. Adjustment, straight lines can be used normally.
Guangzhou Jointair Co., Ltd. , https://www.jointairaccessories.com