Gear pump housing requires two holes for high precision machining. In the medium and small batch production, the general use of general-purpose machine tools and special tooling to processing, this processing method is difficult to achieve accuracy requirements. Our factory internship factory production of this part, from the processing methods, cutting tools, fixtures continue to improve, a better solution to this problem, the processing quality is stable and reliable. 1 pump hole accuracy requirements and processing methods Figure 1 gear pump body processing two holes in the process diagram. As can be seen from Fig. 1, the aperture 12.5 is at level 7, and the two apertures have different ultimate sizes. The larger aperture R18.41 is closer to level 8, and the coaxiality, perpendicularity and position tolerances are required, especially the position tolerance is very small. Therefore, the hole is difficult to process. Figure 1 Pump hole machining process diagram After repeated tests, improvements, is the use of the following processing methods: the two holes on both sides of the processing, 4-φ9 holes after the processing steps, and 4-φ9 a diagonal hole accuracy To φ9H8, for positioning. Then three holes are machined with R18.41 and φ12.5. The first process: In the lathe with rotary chuck car indexing R18.41 hole to R18.31 +0.065 + 0.035 (R18.41 with casting bottom hole), drill φ12.5 hole to φ11.5, and then boring to φ12 .4 ± 0.01. The second process: the design of special composite reamers, lathe (due to drilling spindle rotation accuracy is low, can not use drilling) at the same time reaming R18.41 and φ12.5 coaxial hole. Big hole hinge to R18.41 + 0.055 + 0.025, two small holes hinge to φ12.5S7 size. The tool is mounted on the spindle (remove the chuck) and the tail end of the tool is provided with guide bearings on the clamp. Fixture mounted on the carriage (remove the knife holder), with a straight line indexing fixture. The third process: Drilling machine with a floating reamer to one of the small holes hinge φ12.5F7 size requirements. 2 fixture design hole processing as the second process is the key process, here only describes the fixture design process. (1) fixture program and structure: Select the pump body G surface and two φ9 diagonal holes for the positioning of the fixture with two pins on one side of the positioning. Linear indexing form. Clamp the part with two hook clamps. Figure 2 shows the structure of the fixture (Note: the figure shows only the key dimensions and the main part number). Clamp body 1 is an angle iron, with screws, tapered pins mounted on the carriage. Moving indexing block 2 and clamp body 1 through the dovetail guide rail, and with the bolt 3 lock. The indexing block 2 is provided with a cylindrical pin 4 and a chamfered pin 9 by which the part is positioned on the indexing block 2 and is pressed by the two hook- Seat 6 is used to support the rear end of the tool. With hand-drawn cylindrical indexing on the agency. For the convenience of operation, the workpiece is installed on the right side of the fixture, and the fixture body is provided with holes on the indexing block for the tool to enter the workpiece processing. In order to prevent the chips from entering the joining surfaces of the members 1 and 2, the chip holder 10 is fitted in the hole of the clip body 1. Figure 2 Fixture Structure Figure 1. Clamp body 2. Moving indexing block 3. Locking nut 4. Cylindrical locating pin 5, 12. Bushing 6. Support seat 7. Cylindrical pin 8. Screw 9. Beveling dowel 10 Chip set 11. Riding pin 13. Sealing block 14. Hook press plate mechanism 15. Index alignment mechanism (2) Fixture operation: Place the work piece into two positioning pins, tighten the hook-shaped plate nut, move the carriage vertically The cylinder pin of the fixed mechanism 15 is inserted into the pin hole of the first hole. After machining the first hole, loosen the two lock nuts 3, pull out the cylinder pin of the alignment mechanism 15, move the index block 2 so that the cylinder pin of the alignment mechanism 15 is inserted into the second hole Pin hole, and tighten the nut 3, the processing of the second hole. (3) fixture installation requirements: manufacturing, the indexing agencies for the cylinder pin and bushing 12 with the preparation, with the gap of not more than 0.01mm. Installation, to ensure that the fixture center line K and spindle lathe coaxiality, coaxial tolerance of 0.015mm. P positioning and positioning of the lathe spindle axis perpendicular to the tolerance of 0.02mm. When the fixture is installed and adjusted, the horizontal feed must be locked, and the vertical feed should be set as dead stop iron. (4) Fixture features: The principle of reference coincidence, positioning error is small, higher indexing accuracy. Tool support at both ends, beating small, high precision machining hole size. Clamping reliable, easy to operate. The long-term use of proof, can fully guarantee the processing accuracy requirements, the downside is the process of observation is not convenient.
Residential Sectional Garage Door
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers. The door is balanced by either a torsion spring system or a pair of extension springs.A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security
• Aluminum garage doors are low-cost, light, rust-proof, and feature low-maintenance. They are prone to denting because aluminum is not strong and they are energy-inefficient since aluminum is a highly conductivematerial.
• Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They have also polyurethane insulated base sections, or other type of foam insulation. These premium doors can match steel garage doors, and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units.
• Steel doors have become common and are available in a variety of sizes and styles, provide strength and security, are cost-competitive, and may have optional insulating value. Extra strength is available with two or three layers of galvanized steel with a low gauge number (23-24 gauge steel panels).
• Wood garage doors offer aesthetic appeal, but they are high-maintenance and may be expensive. Low-priced wood garage doors may warp and break easily.
Residential Sectional Garage Door,Automatic Metal Sectional Garage Door,Standard Lift Garage Door Drum,Polyurethane Foam Garage Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.highspeedshutterdoor.com
